DEF Quality Fault Codes:
SPN 3364 Explained
Updated November 2026 - 14 min read - Heavy-Duty Diesel Aftertreatment
SPN 3364 is not proof that the DEF in the tank is bad. The fault family concerns diesel exhaust fluid quality, but the cause can be out-of-spec fluid, a misleading quality-sensor reading, low tank level and aeration, DEF delivery problems, or an SCR performance issue that requires additional tests. Detroit and Cummins/International also use different FMI combinations. This guide explains which codes mean what on documented platforms, which measurements are useful, and why replacing a DEF header or dosing unit before testing the fluid is often the wrong first step.
What Does SPN 3364 Monitor?
In SAE J1939 diagnostics, SPN 3364 concerns Aftertreatment 1 Diesel Exhaust Fluid Tank 1 Quality. DEF is an aqueous urea solution used by selective catalytic reduction (SCR) systems to reduce nitrogen oxides in diesel exhaust. The normal AUS 32 formulation is 32.5% high-purity urea and 67.5% purified water. Quality matters because SCR efficiency depends on delivering the correct quantity of uncontaminated reducing agent.
Some systems have an integrated DEF quality sensor in the tank header. Other calibrations may judge quality indirectly from dosing and exhaust-sensor response. Consequently, a quality code does not automatically identify a failed in-tank sensor, and a valid-looking sensor reading does not prove fluid meets every ISO 22241 purity requirement.
SPN 3364 FMI Breakdown - What the OEM Documents Show
These are documented examples, not a universal FMI list. The Detroit entries refer to specified EPA10/GHG14 DD procedures. The Cummins code mappings are from a bulletin applying to identified International chassis and Cummins calibrations.
| Code | Documented Platform | Meaning in That Procedure | First Diagnostic Direction |
|---|---|---|---|
| SPN 3364 FMI 2 |
Detroit DD EPA10 | Improper DEF quality; the published bulletin lists MIL/CEL and 25% derate for this configuration. | Check ACM software requirements, refractometer reading, DEF pressure and lines, dosing quantity, then SCR conversion response per procedure. |
| SPN 3364 FMI 17 |
Detroit DD EPA10 | Improper DEF quality warning | Use the OEM DEF-quality diagnostic and verification process; do not infer bad fluid or sensor from the warning alone. |
| SPN 3364 FMI 1 |
Detroit DD EPA10 | DEF quality final warning; flashing DEF lamp listed in the applicable bulletin | Confirm fluid and delivery, evaluate related SCR data, and obey the truck's warnings; lamp and engine-reaction strategies vary by model year. |
| SPN 3364 FMI 18 |
Detroit DD GHG14 | Improper DEF quality warning | Check refractometer reading, DEF line condition, dosing quantity, and NOx conversion during the approved test; this is not merely a tank-sensor replacement code. |
| SPN 3364 FMI 11 |
Cummins-equipped International; Fault Code 1715 | DEF quality sensor-related fault; covered by Cummins TSB160031 | Check applicable DEF quality sensor firmware and authorized updates; bulletin cites Navistar AFC 16904/16905 for eligible vehicles. |
| SPN 3364 FMI 10 |
Cummins-equipped International; Fault Code 4277 | DEF quality-sensing fault included in the Cummins/International bulletin | Follow the vehicle's Navistar diagnostic action plan and DEF quality sensor troubleshooting steps. |
| SPN 3364 FMI 15 |
Cummins-equipped International; Fault Code 4842 | DEF quality condition covered by the Cummins/International bulletin | Check DEF level and possible sensor aeration; verify actual fluid quality and follow the approved fault tree. |
| SPN 3364 FMI 18 |
Cummins-equipped International; Fault Code 3867 | DEF quality condition covered by the Cummins/International bulletin | Separate a real fluid issue from low-level sensor aeration, firmware, and other identified faults before replacing the header. |
Important: Two different OEM implementations can use the same FMI for different diagnostic or warning strategies. Confirm the complete fault text in DiagnosticLink, INSITE, or the applicable OEM software, not only the SPN/FMI shown on the dash.
What Counts as Proper DEF Quality?
| Measurement | Reference | How to Use It |
|---|---|---|
| Nominal DEF formulation | 32.5% urea / 67.5% purified water | The normal AUS 32 formulation described by API and Cummins. Use fresh ISO 22241-compliant DEF. |
| Detroit EPA10/GHG14 published diagnostic screening range | 28-36% on the specified refractometer test | This is a fault-tree decision range in particular older Detroit service publications, not a statement that 28% or 36% fluid meets ISO 22241. |
| Detroit GHG14 dosing quantity check | 108-132 mL during the specified service routine | A platform- and procedure-specific metering test. Do not apply the volume or test duration to a different vehicle. |
| DEF purity | ISO 22241 / API-certified product | A refractometer indicates concentration; it does not identify every contaminant or prove compliance with all purity limits. |
Common Symptoms and Related Faults
- Check Engine or emissions warning message
- DEF quality or SCR system warning
- Reduced engine power on some calibrations
- Warning that persists after a refill
- Intermittent message at low DEF level
- No apparent change in engine performance despite an active emissions fault
- SPN 4364 - SCR conversion efficiency fault
- SPN 5246 - SCR operator inducement fault family
- DEF tank level, temperature, or quality sensor codes
- DEF pump pressure or dosing-system faults
- NOx sensor or aftertreatment temperature faults
- Recent refill, fluid storage, or header-service history
SPN 3364 should also be distinguished from SPN 4364, which evaluates SCR NOx conversion efficiency. They can occur together, but they are not the same diagnostic parameter. See the existing guide for the catalyst-efficiency troubleshooting path.
Root Causes That Can Produce SPN 3364
1. Diluted, contaminated, or deteriorated fluid
Incorrect DEF concentration reduces the chemical reducing agent available to the SCR system. Contamination by diesel, coolant, tap water, dirt, or incompatible handling equipment may cause other problems even when a concentration reading looks plausible. Sample the actual tank fluid using clean DEF-compatible equipment rather than relying on the label from the last container used.
2. Low tank level causing incorrect sensor measurement
This is a documented issue, not a speculative one. Cummins Technical Service Bulletin TSB160031 reports that on certain Cummins-powered International vehicles, low DEF level allows air bubbles from fluid movement to disturb the quality sensor's concentration calculation. The bulletin includes SPN 3364 FMI 10, 11, 15, and 18 among the affected codes. A replacement sensor will not address a low-level measurement condition without completing the applicable diagnostic.
3. DEF quality sensor, header, wiring, or firmware
Some vehicles use an integrated DEF tank header containing multiple sensing functions. Connector contamination, wiring faults, a faulty quality-sensing element, or outdated firmware can create unreliable readings. Cummins notes a Navistar firmware field update for eligible SPN 3364 FMI 11 cases. Determine applicability through the authorized service system before replacing hardware.
4. DEF supply or dosing fault
Damaged DEF lines, a metering-unit problem, a restricted dosing valve, or inadequate commanded delivery can affect exhaust-treatment performance. Detroit's published SPN 3364 paths do not stop at a fluid sample: they inspect lines, compare pressure, conduct a dosing quantity test, and use SCR performance information. A dosing fault requires a failed delivery test or related diagnostic evidence.
5. Other SCR or exhaust-sensor faults
Incorrect NOx readings, temperature-sensor faults, or true catalyst inefficiency can complicate the quality monitor. The engine may set other fault codes that must be diagnosed first. Forcing a sensor or catalyst replacement from SPN 3364 alone skips the tests that show which system is actually out of specification.
How to Diagnose SPN 3364 - Step by Step
- Record the full diagnostic context. Identify engine/vehicle model, emissions year, OEM SPN/FMI description, related active codes, ECM/ACM calibration, DEF warning state, tank level, and conditions when the fault appeared. Save the log before clearing anything.
- Address primary electrical or system faults. Look for quality-sensor communication, tank temperature/level, DEF pressure, supply-voltage, NOx, and dosing faults. Follow the OEM's priority list; a secondary quality warning may persist until the primary failure is corrected.
- Check tank level and recent refill history. A very low tank can expose an aeration-sensitive quality sensor on certain Cummins/International platforms. Verify whether an eligible firmware update applies before condemning a header.
- Take a representative DEF sample. Use clean tools and measure concentration with a DEF refractometer. Compare the reading against the vehicle's official test limits. A correct concentration is useful evidence, but does not establish that all ISO 22241 purity limits have been met.
- Correct genuinely out-of-spec or contaminated fluid. Follow the OEM drain, cleaning, flushing, and refill procedure if required. Do not assume that adding fresh DEF on top of questionable fluid will restore acceptable quality.
- Check DEF supply lines and measured pressure. Inspect kinks, leaks, disconnects, damaged connectors, and pressure readings as specified by the fault tree. Avoid assuming the pump, header, or pressure sensor is faulty without the corresponding measurement.
- Perform the approved DEF quantity test when required. The Detroit GHG14 bulletin, for example, specifies 108-132 mL during its own dosing routine. Measure against the procedure for the exact vehicle; failed volume can direct diagnosis toward a doser or metering system.
- Evaluate SCR conversion only after fluid and dosing checks. Use the OEM-authorized test to chart inlet/outlet NOx, temperatures, and efficiency. This distinguishes a quality/delivery problem from an exhaust sensing or catalyst-related concern. See the SPN 4364 guide for additional conversion-efficiency context.
- Verify repair and warning recovery. Perform the exact OEM confirmation and inducement-recovery procedure; some monitors require a complete operating or service cycle to pass. Check that the underlying fault is inactive and that warning conditions clear under approved criteria.
Should You Replace the DEF Header, Pump, Doser, or NOx Sensor?
A DEF header or quality sensor should be selected only after confirming a persistent sensor/firmware/harness fault and ruling out fluid-level and sample issues. A DEF pump or metering unit needs an appropriate pressure or delivery failure. A doser needs a failed dosing quantity or functional test. A NOx sensor needs its own plausibility or correlation evidence. A SCR catalyst is considered only after the fluid, delivery, and sensor branches of the applicable efficiency diagnostic have been completed.
Part fitment depends on the VIN or engine serial number, emissions architecture, tank arrangement, connector, software version, and the original part number. Some DEF headers combine level, temperature, and quality sensing; others do not. Confirm the correct component before placing an order.
Frequently Asked Questions
Not necessarily. The code family concerns DEF quality, but the problem can be actual fluid composition, a bad quality measurement, low DEF level causing aeration, delivery faults, or related aftertreatment conditions. Test a representative fluid sample and follow the vehicle-specific diagnostic sequence before replacing any part.
Normal AUS 32 DEF is formulated at 32.5% high-purity urea and 67.5% purified water. Use fluid conforming to the applicable ISO 22241 specification. The 28-36% number found in some older Detroit service trees is a diagnostic screening threshold, not the acceptable DEF product specification.
On certain Cummins-powered International trucks, yes. Cummins TSB160031 reports that air bubbles associated with a low DEF level can distort the quality sensor's calculated concentration. The bulletin covers several SPN 3364 FMI variants and includes a sensor firmware update path for eligible FMI 11 vehicles.
In the Detroit EPA10 service bulletin, it is an improper DEF quality fault. The documented diagnostic checks software level, refractometer concentration, DEF pressure, lines and metering, then SCR performance. The published EPA10 bulletin lists a 25% derate for its configuration; do not apply that response to every Detroit model year.
No. Detroit's GHG14 FMI 18 procedure examines fluid concentration, DEF line integrity, dosing quantity, and SCR performance. Cummins/International also lists FMI 18 in a bulletin about inaccurate quality calculation at low fluid level. Both examples show why sensor replacement is not automatic.
A refill may correct a low-level condition, but it does not necessarily remove contaminated fluid, repair a failed sensor, restore dosing, or satisfy the controller's confirmation requirements. If the tank fluid is genuinely out of specification, the OEM procedure may call for draining and flushing rather than topping off.
SPN 3364 relates to DEF quality information or quality-related monitoring. SPN 4364 concerns SCR conversion efficiency: whether the aftertreatment is reducing NOx as expected. Poor fluid quality can contribute to an efficiency problem, but one code does not establish the cause of the other. Diagnose related faults in the manufacturer-prescribed order.
That depends on the specific engine and emissions calibration, warning state, and whether a power reduction or inducement is active. Follow the vehicle's displayed warnings and OEM operating instructions. Avoid assuming a truck is safe to continue operating simply because it initially shows little change in power.
No. A refractometer is mainly a concentration check. API specifically cautions that correct concentration alone does not guarantee compliance with all ISO 22241 purity requirements. If the fluid source or contamination is in doubt, use the OEM's complete sampling and evaluation procedure.
Technical References
Figures and examples are tied to published sources: Detroit EPA10 SPN 3364 FMI 1/2/17 bulletin, Detroit GHG14 SPN 3364 FMI 18 bulletin, Cummins TSB160031 for specified International vehicles, and API information on DEF formulation and ISO 22241. Consult current OEM service information for the specific VIN, ESN, and software calibration.
Need a DEF or Aftertreatment Component?
Browse DEF headers, pumps, dosing equipment, sensors, and other aftertreatment parts. Identify the failed component through proper diagnosis, then contact Wisent Parts Center to verify the correct part number and fitment before ordering.
Explore Aftertreatment Parts